CognitiveTPG A798 Manual de Instruções Página 52
- Página / 121
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Chapter 4: Programming Commands52
Revision C 12/09
A798-PG00001C
Dene extended user-dened character set
ASCII US & s c1 c2 [character 1 data] ... [character k data]
Hexadecimal 1F 26 s c1 c2 [character 1 data] ... [character k data]
Decimal 31 38 s c1 c2 [character 1 data] ... [character k data]
Values and ranges:
s = the number of dot rows in the character cell (maximum 64)
c = the ASCII codes of the rst (c1) and last (c2) characters respectively
c1 = Hex 20–FF (20 is always printed as a space)
c2 = Hex 20–FF (20 is always printed as a space)
To dene only one character, use the same code for both c1 and c2
j = s/8 = the number of bytes (vertically) in the character cell
k = c2 – c1 + 1 = the number of characters to be dened in this command string
[character i data] = [ni d1 ... d(j x ni)] for 1 ≤ i ≤ k
ni = the number of dot columns for the ith character, 1 ≤ ni ≤ 16
d = the dot data for the characters
The number of bytes for the ith character cell is j x ni.
The bytes are printed down and across each cell.
See the illustration.
Denes and enters downloaded characters into RAM. The command may be used to overwrite single characters. User-
dened characters are available until power is turned off or the Initialize Printer command (1B 40) is received.
Any invalid byte (s, c1, c2, n1, n2) aborts the command.
Select or cancel underline mode
ASCII ESC - n
Hexadecimal 1B 2D n
Decimal 27 45 n
Value of n: Decimal Hex
0, 48 30 = Cancel underline mode
1, 49 31 = Select underline mode
2, 50 32 = Select double thickness underline mode
Default: 0 (Cancel underline mode)
Turns underline mode on or off. Underlines cannot be printed for spaces set by the horizontal tab, set absolute start
position, or set relative print position commands.
This command and the Select Print Mode(s) command (1B 21) turn underline on and off in the same way.
Exceptions
This command is ignored if n is out of the specied range.
Related information
In A793 emulation, this command is unrecognized and the parameter n is put into the print buffer.
- Programming Guide 1
- Contents 3
- 4 Revision C 12/09 4
- 6 Revision C 12/09 6
- 8 Revision C 12/09 8
- A798 Programming Guide 10
- Chapter 1: About this Guide 10
- Revision C 12/09 10
- A798-PG00001C 10
- Start-up Diagnostics 11
- Runtime diagnostics 12
- Remote diagnostics 12
- Comm Class” 13
- Indicators 14
- Printer conguration 15
- Conguring the printer 16
- Communication interface 17
- Diagnostic modes 18
- Printer emulations 19
- Overview of commands 23
- Comparison to A793 23
- Character appearance 25
- Print zones 25
- Rotated printing commands 26
- Emulation modes 27
- Commands listed by function 29
- Text characteristics 30
- Graphics 31
- Bar codes 32
- Page mode 32
- User data storage 32
- Command conventions 33
- Command descriptions 34
- Generate tone 35
- Initialize printer 35
- Select cut mode and cut paper 38
- Print test form 38
- Print and paper feed 39
- Add n extra dot rows 40
- Print and feed paper 41
- Print and feed n lines 41
- Horizontal tab 42
- Set column 42
- Set vertical line spacing 44
- Set horizontal tab positions 44
- Set relative print position 45
- To move to the left: 45
- Select justication 46
- Set left margin 46
- Set printing area width 47
- Text characteristics commands 48
- Select pitch (column width) 49
- Select print mode 50
- 51
- Cancel user-dened character 53
- Select or cancel italic print 54
- Select character size 57
- Select bit image mode 60
- Print Flash Logo 62
- Dene Flash Logos 62
- Select the current logo 62
- Dene downloaded bit image 63
- Print downloaded bit image 64
- Print raster graphics 65
- Status command introduction 65
- Batch mode 65
- Transmit paper sensor status 67
- Transmit printer ID 68
- Transmit status 71
- Send printer software version 72
- Real time commands 73
- Moving data through the buer 74
- Real time status transmission 74
- Real time request to printer 77
- Real time commands disabled 78
- Unsolicited status mode 79
- Print bar code 84
- Print multiple barcodes 85
- 29 107 n d1... 00 87
- 29 107 m nL nH d1... dn 87
- Select PDF 417 parameters 88
- Select bar code width 89
- Sample symbol description: 89
- Select page mode 91
- Select standard mode 92
- Set print area in page mode 93
- Execute macro 95
- Erase user ash sector 99
- Flash download 100
- Get rmware CRC 101
- Return microprocessor CRC 101
- Erase selected ash sector 102
- Reset rmware 102
- Return main program ash CRC 102
- Appendix A: 104
- Appendix B: 108
- Resident Character Sets 108
- Code page 737 (Greek) 109
- Code page 850 (Multilingual) 110
- Code page 852 (Slavic) 111
- Code page 857 (Turkish) 112
- Code page 860 (Portuguese) 114
- Code page 862 (Hebrew) 115
- Code page 865 (Nordic) 117
- Code page 866 (Cyrillic) 118
Manuais e produtos relacionados com Digitalizar e Imprimir CognitiveTPG A798
(36 páginas)© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.040 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais